How to remove metal fence posts set in concrete?
The article aims to answer the question “How to remove metal fence posts set in concrete?”. It will also mention the tools you need to fix the trellis to fence panels in concrete posts.
The article will also explain what concrete posts are. Read on to need more:
How to remove metal fence posts set in concrete?
You need to read the following instructions to remove metal fence posst in concrete:
- When removing concrete post footings, put on your work gloves. If you have access to a tractor, you may raise the post and foot out of the ground by hoisting a chain around the post’s base.
- Remove the concrete footing from the post’s base by sledgehammering it apart.
- Start by digging around the steel fence posts and concrete with your shovel. When you eliminate them, it will be much easier for you.
- Find the bottom of the concrete using your hands. Dig with gloves on and then move the steel fence posts back and forth to loosen them.
- Drilling or demolishing concrete is made possible by an electro-pneumatic piston that generates significant impact energy.
- Fill the hole to a depth of about six inches with gravel. To fill the hole to a depth of three inches below the soil’s surface, sprinkle rapid-set cement mix powder over the gravel.
- In order to guarantee that the fence post is level vertically, use a rubber mallet and lay a spirit level on top of the post.
What do I need to remove metal fence posts set in concrete?
You need the following things to remove metal fence posts set in concrete:
- Fence panels
- Drill
- Nail set
- Trowel
- Concrete posts
- Protective gear
- Mask
How to remove fence posts from concrete?
To remove fence posts from concrete, follow the given steps:
- In the first stage, the remaining fence post must be removed or broken apart. Unless the wood is really old and rotted, this should be a simple task.
- Use the weight of your digger bar chisel to smash through the old fence post. It should disintegrate and fracture into pieces. Remove as much of the original wood pillar as you can before moving on.
- Pulling the post out in one piece is possible if it is old and loose.
- Dig a small hole between the concrete footing and the earth using your shovel. You don’t have to dig very far to get your digger bar through.
- It’s important to keep in mind that the more you dig up, the more difficult it will be to replace an old post with a new one later.
- Breaking up the concrete footing will be necessary to remove it from the posthole. Fortunately, cracking concrete into tiny fragments is very simple if you have the proper equipment.
- To complete this mission, you’ll need a large and heavy instrument, which you may employ in a number of ways. Both a sledgehammer and a digger bar chisel may be used. Using excessive force may cause the footing to crumble, so don’t hesitate.
- Remove the cracked concrete footing from the posthole by reaching down and removing it. Even if you can pull it out of the posthole in two or three pieces, you may have to break it up more to get it out completely.
How to replace fence panels in concrete posts?
If you want to replace the fence panels in concrete posts, continue reading the given steps:
- The panel should be placed on the ground with the side that you wish to face your property facing outward-facing.
- You’ll need to place two of your pieces of wood on top of the panel, going top to bottom approximately a fourth of the way in from each of the corners. Make sure they’re in the right place.
- Your panel’s legs need to be constructed now. They’ll create an H-shape, and the panel will sit on top of them.
- Place two more pieces of wood parallel to each other on the ground, with the same space between them as the two that are fastened to the panel. Position them. You’ll need to nail your 6-inch-wide length across these two.
- At each joint, use a minimum of two nails spaced apart by a reasonable amount. This stops the timber from twisting and gives the construction a more solid foundation.
- Attach the H-shaped legs to the bottom of the wood lengths you fastened to the panel now, and clamp them in place.
- Remember that when the panel is reinstalled, the side facing you will be the side that is facing up. If you need to remove the clamps from one side, make sure it’s simple.
- Position the bottom of the legs at the bottom of the empty space where you want the fence panel to end up once you’ve rolled the entire thing over and turned it over again.
- To elevate the whole construction vertically, hoist the panel’s top above your head and move ahead. The bottom of the fence panel should be positioned slightly below the tops of the posts once it is completely upright.
- Depending on how far apart the posts are, you may be able to move them just enough to fit the bottom of the panel between them, or you may need a few more inches of lift to get it in place.
- Remove the clamps holding the legs in place after you’ve got the bottom of the panel in place between the posts. After nailing in the two pieces of lumber, remove them and you’re done!
How can I install fence panels in existing concrete posts?
To install the fence panels in existing concrete posts:
- Reinforce Your Fence Panel. You may want to think twice before removing your fence panel from the pillars that support it on each side.
- To place the panel in front of your property, place it on the ground with the desired side facing up. A quarter-inch or so in from the sides, place your two pieces of wood vertically on top of the panel.
- Make sure they’re in the right place. The nails I used for this area are an alternative to clamps; I only had two clamps on hand, so I used them instead).
- Now that you’ve completed the panel, it’s time to add legs. They’ll create an H-shape, and the panel will sit above them.
- Make sure that the distance between the two pieces of wood that are attached to the panel is equal to the distance between the two pieces of wood that are on the ground. You’ll need to nail your 6-inch-wide length across these two.
- Ensure that at least two nails are used at each joint. As a result, the wood is less likely to warp and the structure is more stable.
- Attach the H-shaped legs to the bottom of the wood lengths you fastened to the panel now, and clamp them in place.
- Once the panel has been reinstalled, the side that is facing up will be the one facing you. If you need to remove the clamps from one side, make sure it’s simple.
- Make sure the bottom of the structure’s legs are positioned at the bottom of the gap where you want your fence panel to end up before rolling it over.
- As you move forward with the panel raised over your head, the whole structure will be in a vertical posture. A fence panel that is 12 feet in the air, with the bottom just below the top of the posts, should be completed when the panel is entirely vertical.
- To slot the panel into place, you may just need to raise the tops of the posts a few millimeters (the posts move significantly more at their tops than their bottoms), or you may need to elevate it a few more inches.
- Remove the clamps holding the legs in place after you’ve got the bottom of the panel in place between the posts. In the first stage, you nailed on two pieces of wood. Now you may remove them.
How to fit concrete fence posts?
Following instructions would help you if you want to fit concrete fence posts:
- To place your concrete posts, you’ll need to drill appropriate holes. Using a gravel board, measure the distance between each fence post before drawing out the hole. Additionally, the hole should be around two feet deep.
- Make sure the post is inserted into the hole and that everything is in the correct position.
- Make sure that your concrete gravel planks fit snugly between the posts. After that, fill each hole with 40 kg of quick-setting concrete mix.
- To start the concrete setting, add the necessary water and keep the posts in place. Mixing the dry mix with water before filling the hole is also an option.
- Before fitting the fence panels into the posts, let the concrete dry for at least one night.
- Enjoy your new fence as soon as the panels are installed.
- Make sure you obtain the right quantity of concrete for the task, whether you’re installing concrete fence posts or doing any other concrete DIY project.
- Make use of the Total Concrete concrete calculator to receive an exact estimate for your project.
What is a concrete fence post?
Concrete fence posts include four internal steel reinforcing bars, making them a long-lasting alternative to timber posts.
You can rely on the long-term durability of our concrete fencing posts, which are resistant to ground decay. Fence posts with a slotted design can accommodate all of our fencing panels.
Backbone of a robust and appealing garden fencing is the use of concrete fence posts. Concrete posts are the way to go if you want your fence to be more stable in the rainy season.
If you’re merely seeking to beef up your existing posts, our concrete spurs are a good option. Concrete spurs are short concrete posts that can be bolted to your existing posts for further support.
To put it another way, if you enjoy the aesthetic of the wooden posts, you may do your part to keep them sturdy.
How to install concrete posts?
To install concrete posts:
- Rather than using wood supports, concrete slotted posts for fencing or regular trellis panels provide a long-lasting and simple solution to this problem. If necessary, the trellis or panels can be removed and replaced.
- For added security, you can install panel security brackets to keep the panels from being lifted out.
- Each post has a weathered (Pyramid) top that is four-sided.
- Slotted posts and fence panels work well with concrete gravel boards because they keep the bottom of the fence panel off the ground and prevent it from deteriorating prematurely.
- If the fence will be installed on a slope, you will need to have the posts lengthened to allow the panels to step down it.
- There are two common methods for anchoring concrete posts: a dry mix (approximately 7 to 1 with no additional water added) or a post-mix (about 7 to 1 with no further water added) (follow directions on the bag).
- The size and depth of the hole will determine how much of each is needed. To ensure a snug fit around the post, aim for a hole diameter of 200 to 250mm (8′′ to 10′′).
- The hole should be at least 600 mm (2 feet) deep, regardless of the fence’s height.
- We recommend utilizing a longer post and increasing the hole depth to a minimum of 750mm (2′ 6′′) for fences exceeding 1.5m in height.
Conclusion
To remove a dirt-encased metal fence post, you’ll need some serious strength, a shovel, and a lot of time. You may use a vehicle jack, tractor, or a lever made of timber to remove a metal fence post that is embedded in concrete.
You may require a jackhammer if it’s embedded in a slab of solid concrete. When removing concrete post footings, put on your work gloves. If you have access to a tractor, you may raise the post and footing out of the ground by hoisting a chain around the post’s base.
Remove the concrete footing from the post’s base by sledgehammering it apart.
Frequently asked questions (FAQS): How to remove metal fence posts set in concrete?
How to remove metal fence posts set in concrete?
When removing concrete post footings, put on your work gloves. If you have access to a tractor, you may raise the post and foot out of the ground by hoisting a chain around the post’s base. Remove the concrete footing from the post’s base by sledgehammering it apart.
Start by digging around the steel fence posts and concrete with your shovel. When you eliminate them, it will be much easier for you. Find the bottom of the concrete using your hands. Dig with gloves on and then move the steel fence posts back and forth to loosen them.
Drilling or demolishing concrete is made possible by an electro-pneumatic piston that generates significant impact energy.
How to remove rotten fence posts set in concrete?
In the first stage, the remaining fence post must be removed or broken apart. Unless the wood is really old and rotted, this should be a simple task.
Use the weight of your digger bar chisel to smash through the old fence post. It should disintegrate and fracture into pieces. Remove as much of the original wood pillar as you can before moving on. Pulling the post out in one piece is possible if it is old and loose.
Dig a small hole between the concrete footing and the earth using your shovel. You don’t have to dig very far to get your digger bar through. It’s important to keep in mind that the more you dig up, the more difficult it will be to replace an old post with a new one later.
How to replace fence panels in concrete posts?
The panel should be placed on the ground with the side that you wish to face your property facing outward facing.
You’ll need to place two of your pieces of wood on top of the panel, going top to bottom approximately a fourth of the way in from each of the corners. Make sure they’re in the right place. Your panel’s legs need to be constructed now. They’ll create an H-shape, and the panel will sit on top of them.
Place two more pieces of wood parallel to each other on the ground, with the same space between them as the two that are fastened to the panel. Position them. You’ll need to nail your 6-inch-wide length across these two.
How to install fence panels in existing concrete posts?
Reinforce Your Fence Panel. You may want to think twice before removing your fence panel from the pillars that support it on each side.
To place the panel in front of your property, place it on the ground with the desired side facing up. A quarter-inch or so in from the sides, place your two pieces of wood vertically on top of the panel.
Make sure they’re in the right place. The nails I used for this area are an alternative to clamps; I only had two clamps on hand, so I used them instead).
How to fit concrete fence posts?
To place your concrete posts, you’ll need to drill appropriate holes. Using a gravel board, measure the distance between each fence post before drawing out the hole. Additionally, the hole should be around two feet deep.
Make sure the post is inserted into the hole and that everything is in the correct position. Make sure that your concrete gravel planks fit snugly between the posts. After that, fill each hole with 40 kg of quick-setting concrete mix.
To start the concrete setting, add the necessary water and keep the posts in place. Mixing the dry mix with water before filling the hole is also an option.
How to fix trellis to fence with concrete posts?
Battens attached to the fence guarantee that the trellis has space between it and the fence for plants to coil themselves around it.
In general, battens should be between 30mm and 60mm wide and the length of the trellis, depending on the size of your trellis. Inscribe on the fence where the trellis’s top and bottom will be.
When you’re done, put the battens into place with a drill and wood screws. The middle of your trellis might benefit from a separate trellis. Fix the trellis to the battens, and then plant your climbers below.
What is a concrete fence post?
Concrete Slotted fence posts have four internal steel reinforcing bars, making them a long-lasting alternative to timber posts.
You can rely on the long-term durability of our concrete fencing posts, which are resistant to ground decay. Fence posts with a slotted design can accommodate all of our fencing panels.
Backbone of a robust and appealing garden fencing is the use of concrete fence posts. Concrete posts are the way to go if you want your fence to be more stable in the rainy season.
Bibliography
Extending Concrete Fence Posts to Add Trellis. Retrieved from: https://community.screwfix.com/threads/extending-concrete-fence-posts-to-add-trellis.208173/
Trellis on Top of Fence With Concrete Fence Posts. DIY doctor. Retrieved from: https://www.diydoctor.org.uk/forums/trellis-on-top-of-fence-with-concrete-fence-posts-t41351.html
