How to install an electrical box in a concrete block?

The article aims to answer the question “How to install an electrical box in a concrete block?”. It also aims to highlight the tools and materials you need for the job. The article will also mention the ways to install the electrical cables in a concrete block safely.

How to install an electrical box in a concrete block?

  • Mark the course and locations of your electrical conduit lines and electrical boxes according to your drawings. To be on the safe side, a tape measure is a must. 
  • To ensure that the locations of your items are compliant with building codes, the electrical engineer assigned to your design team has already checked them out. 
  • Afterwards, the local body in charge of ensuring that all building designs granted a building permit meet with code has examined and authorized their work. 
  • In order to pass your final examination, you must be able to match your designs’ dimensions as closely as possible in real life.
  • The electrical conduit should be run in the shape. If you want to connect the conduit to the building’s electrical system later, you’ll need to leave at least 12 inches of it outside the form. 
  • When you’re finished, use side-cutting pliers and wire tie wire to secure your conduit to your concrete form (these will also let you cut the wire without an additional tool). Try to knot it at the location where the horizontal and vertical bars intersect every 4′ along the conduit once you’ve done this. 
  • This will give you a tie that can withstand the weight of the concrete pour without slipping out of place.
  • Push a long tie wire through the conduit with the end of your nylon rope tied to it. Because the yarn is usually already within the conduit, it may not be necessary to thread the conduit. 
  • Using duct tape to fuse the conduit pieces together as you thread them is the best method. This yarn will be used to pull the real electrical wire through the conduit when you pour the wall.
  • Make sure the entrance of your electrical boxes is flush with the face of the concrete form when you place them within the concrete wall form. Using nails, attach the boxes to the wall. 
  • Outlets, switches, junctions, and control panels may all be found in an electrical box (to name a few styles). Connect the conduit to the box and tape the nylon string inside the box opening to prevent it from falling back into the conduit during the pour. 
  • Don’t forget to take note of any construction regulations that may affect where you arrange your components on your plans. When it comes to the installation of electrical boxes, they could specify a precise measurement. 
  • In order to keep everything in line with local regulations, you must adhere to the specifications laid forth in your plans. Specifically, don’t depart from the placements specified.
  • Call for an inspection. The concrete pour may commence after the building inspector has given his or her approval. 
  • Installing the necessary switches, outlets, connections, or other electrical components may be done after the concrete has hardened and the forms have been removed.

What do I need to install an electrical box in a concrete block?

  • Outlet box
  • Hammer
  • Drill
  • Switches 
  • Junctions
  • Control panels
  • Duct tape
  • Nail set

How to install an electrical outlet box in a concrete block?

  • Make use of the empty places where two blocks meet to route your cable line. Your cable will have a route when concrete blocks are installed with hollow parts aligned.
  • A hole for the outlet box should be made. In order to help you break the barrier, draw a line. It’s best to use a carbide-tipped drill, but if this isn’t an option, a star drill will suffice. 
  • Using a ball peen hammer, break away the remainder of the concrete from the corners of your outline.
  • Drill a hole in the mudsill above the concrete wall to run the cable. If you’re fishing via cavities, make sure this hole is parallel to those cavities.
  • When working in the caverns, a chain is a useful tool for getting past any blockages. It is possible to meet impediments, such as extra mortar that was placed in the cavities during building by the mason. 
  • With a long, hefty chain, you can fish through the gaps. To make sure the cable has a straight shot through, try jiggling it about from above.
  • Your wire should be linked to a home circuit by attaching to a chain and then being pulled up out of the cavities. In order to avoid the cable from coming free when you are tugging it, ensure that the connection is solid.
  • Using a utility knife, snip the cable that emerges from the hole in which the outlet will be installed. At least six inches of cable should be left protruding from the wall. Land the cable in the box with the help of a cable connection.
  • The box should be slid into the concrete hole. Screws suitable for anchoring in concrete should be used to secure the box to the floor. A rotating hammer may be used to make pilot holes for the screws. It is best to use expanding foam for this purpose.

How to install electrical cables in concrete walls?

  • You may wish to consult an A/V expert for this task. It’s best to avoid running A/V cables too near to circuit electrical connections so that the distance between the site of usage and the service connection is as short as feasible. 
  • The distances involved should be documented on a materials list. To cover the distance, you’ll need more than the bare minimum of cable. Allow additional time for connections to be made and for the removal of any impediments. 
  • Ten to fifteen percent additional cable is a reasonable rule of thumb when purchasing cable. In addition to the cable, you’ll need wall plates, connectors, low-voltage electrical boxes, and nail plates for the studs in which you’ll be drilling.
  • Make holes in the studs and other frame parts using a drill and spade bit for the cables. Using a drill, drill a hole in the middle of each stud that is big enough to enable the wires to pass through, but never more than 40% of the stud width. 
  • In order to prevent drywall fasteners from coming into touch with the cables, nail plates should be affixed to the front of each hole.
  • The holes may be used to suck in wires. A fish tape or a fish stick may be used if you need to transfer cables through the wall plates and onto a level above or below your current location. 
  • Keep a few extra inches of cord on each end just in case. Using suitable staples or clamps, secure cables at 4-1/2-inch intervals. Make sure you place the clamps approximately 1 foot from each connector.

Conclusion

It might be difficult to install an outlet box in a concrete block. Surface mounting all conduit with pressure-treated wood that has been attached to the wall is the simplest technique to offer electricity in locations with concrete block walls. 

In order to get a flush-mounted outlet, you must first place a box in the wall. The most practical way is to use a cable inserted into the hollow cores of the blocks to pull the wires up from the ground. 

Obstructions in the cavities, such as leftover concrete from construction, might cause problems.

Frequently asked questions (FAQS): How to install an electrical box in a concrete block?

How to install an electrical box in a concrete block?

Mark the course and locations of your electrical conduit lines and electrical boxes according to your drawings. To be on the safe side, a tape measure is a must. To ensure that the locations of your items are compliant with building codes, the electrical engineer assigned to your design team has already checked them out. 

Afterwards, the local body in charge of ensuring that all building designs granted a building permit meet with code has examined and authorized their work. In order to pass your final examination, you must be able to match your designs’ dimensions as closely as possible in real life.

How to install electrical cables in concrete walls?

You may wish to consult an A/V expert for this task. It’s best to avoid running A/V cables too near to circuit electrical connections so that the distance between the site of usage and the service connection is as short as feasible. 

The distances involved should be documented on a materials list. To cover the distance, you’ll need more than the bare minimum of cable. Allow additional time for connections to be made and for the removal of any impediments. 

Ten to fifteen percent additional cable is a reasonable rule of thumb when purchasing cable. In addition to the cable, you’ll need wall plates, connectors, low-voltage electrical boxes, and nail plates for the studs in which you’ll be drilling.

Bibliography

Cassandra Tribe. How to Install Electrical in Concrete Walls. Retrieved from: https://homesteady.com/12241556/how-to-install-electrical-in-concrete-walls

CHARLES W. ST.CLAIR. How to Install an Outlet Box in Concrete Block. Retrieved from: https://www.hunker.com/13402474/how-to-install-an-outlet-box-in-concrete-block

What was missing from this post which could have made it better?

Leave a Comment