How to hang curtains on concrete walls?

The article aims to answer the question “How to hang curtains on concrete walls?”. It will also mention all the possible and easy ways you can hang your stuff on concrete walls. Read on to know more:

How to hang curtains on concrete walls?

• It is necessary to make pilot holes in the concrete before you can hang curtain rods and other items like hooks. 

• Screws can be inserted into these little holes that have been bored into the concrete’s surface.

• Drilling pilot holes to house the concrete anchors needed to hang a curtain rod on cement is an important step in the installation process. These screws are designed to secure the curtain brackets in place by anchoring into the concrete. 

• In order to ensure that the anchors and screws go all the way into the rod bracket and securely secure it to the concrete, you must use the correct drill bit size and make the holes deep enough.

• The plastic brackets for the curtain rod should be attached to the wall using a tape measure. It is recommended that the brackets be hung 4 to 6 inches from either side of the window. 

• When you hang the curtains, this will ensure that the window is entirely covered.

• Place a curtain rod bracket in the desired spot on the wall of the block. Mark the locations of the curtain bracket’s mounting holes using a pencil. Four holes are common on most brackets. 

• Make sure the pencil marks are dark enough to be seen when the bracket is removed. Make sure to repeat this technique with the opposite bracket.

• Verify that the drill’s masonry bit is the correct size by looking at the screw packing. The correct masonry bit size is essential. 

• A 5/32-inch bit is needed for a 3/16-inch concrete screw, and a 3/16-inch bit is needed for a 1/4-inch concrete screw. To ensure that the curtain rod will fit through the hole, make sure you use the correct bit size.

• Drill holes with a masonry bit where the marks you put on the wall are placed using the hammer-drill setting while wearing safety goggles. Screw all the way into the anchor’s core. 

• If you don’t insert the screw far enough, it won’t go in. To do this, simply place the plastic anchor in its designated hole. You should be able to tap it into the hole with a hammer, but it should be snug.

• Hand-tighten the screws in the bracket holes until the bracket is securely fastened to the anchors.

• Make sure the screws holding the bracket to the wall are tight enough so that it is secured straight to the wall. If you screw it in incorrectly, it will be crooked when you remove it.

• Activate the drill’s drill function instead of hammer mode. Each screw should be carefully drilled in until it is firmly in place. The bracket should be screwed in all the way. 

• Make sure it’s secure. If the bracket moves at all, make sure the screws are all firmly in place. Drill a few additional holes if necessary to remove any that have come loose.

• Hook up your curtain rods and hang your curtains from the brackets. You’ve done a great job, so take a moment to admire your efforts.

What do I need to hang curtains on concrete walls?

• Curtain rods
• Drill machine
• Screws
• Hammer
• Gloves
• Goggles
• Command hooks

How to hang curtains on concrete walls with command hooks?

• To hang your curtain rod, you’ll require at least two Command Hooks. It is necessary to use a third Command Hook if your window is wider than 30 inches.

• Mark the locations on your wall where each curtain hook will be attached once you’ve carefully measured your curtains.

• Apply the Command strip adhesive on the hook by peeling the backing off of it.

• For at least 30 seconds, press the Command Hook firmly into the wall and repeat with the other hook.

• Curtains should not be hung until at least 30 minutes have passed.

How to hang heavy curtains on concrete walls?

• With the correct tools and materials, you can easily hang things on a cement wall. Brick hooks and Command Strips make it as simple as hanging things on drywall to do the job. 

• Command Strips may be the greatest option if you’re trying to hang something that isn’t too hefty. Use brick hooks if you have a large piece of art or a heavy mirror.

• Check the packaging for any specific weight limitations. In order to secure your belongings, Command Strips combine hook and loop technology and a specific adhesive that can be removed.

• A hook and loop part for the wall and a section for your personal belongings can be attached to each other. The protective backing can be peeled from one side of the strip and attached to the back of your belongings. 

• Level hanging and weight distribution may necessitate the use of more than one strip. Put as many stripes on the back of your things as you need to.

• Decide where on the cement wall you wish to hang your things. Remove the strip’s protective backing from the wall. 

• For at least 90 seconds, press your belongings hard against the cement wall. Determine how long to push your items against the cement wall using the instructions on the Command Strips box.

How can I hang curtains on concrete walls with fasteners?

• If you use the appropriate fasteners, mounting curtain rods in concrete is as simple as installing them on any other type of surface. 

• In order to install the curtain rod hardware in cement, swap out the nails or screws that came with your rods for concrete fasteners. 

• To install curtain rods in cement, you must first understand how to properly install concrete fasteners so that the curtain rods do not come loose from the wall.

• Decide where you want the curtain rod hardware to be placed. If necessary, use a pencil or marker to make a hole for a screw through one side of curtain rod hardware while holding another side in place.

• To use the selected masonry screws, use a masonry drill bit with the corresponding size. This information can be found on the box label for the concrete screw.

• Put on your goggles or safety glasses.

• Then, using a drill and a masonry drill bit, make pilot holes in the wall where each screw will go. Drill the hole a half-inch deeper than the length of the concrete screws you’ve chosen to use.

• A straw can be used to remove the dust from the hole. To clear the hole, place a straw in it and shield your eyes before blowing through it.

• Drill pilot holes in the cement and insert concrete screws through the curtain rod hardware. Use a drill with a screwdriver bit to tighten the screws.

• The distance between the window’s edge and the side of the installed hardware should be measured. This measurement can be used to put a mark on the other side of the window for the hardware.

• Using a level, hold the other side’s hardware up to the cement mark on the opposite side of the window and adjust it until it’s perfectly level. 

• Make sure that the level is long enough by placing a long, straight board across it and holding the curtain rod hardware on the opposite side against it. 

• On top of the board, place the level. Make sure the hardware is level with the installed hardware by adjusting the leveling screws until the level shows the hardware is level with the installed hardware.

• Place a pencil or marker to mark the placement of the screw holes.

• As before, use an appropriate masonry bit to drill the holes. With a straw, blow the dust out of the perforations. Insert the screwdriver bit into the drill and screw the hardware into place.

• Install the curtain rod hardware as instructed on the package and hang the curtain rod.

Conclusion 

In a building with concrete walls, it may seem impossible to hang a curtain rod. However, there are ways to get around this obstacle. It’s a good thing that this task can be completed. 

If you follow a few simple instructions, you can hang drapes on concrete. It is necessary to make pilot holes in the concrete before you can hang curtain rods and other items like hooks. 

Screws can be inserted into these little holes that have been bored into the concrete’s surface.

Frequently asked questions (FAQS): How to hang curtains on concrete walls?

How to hang curtains on concrete walls?

It is necessary to make pilot holes in the concrete before you can hang curtain rods and other items like hooks.  Screws can be inserted into these little holes that have been bored into the concrete’s surface.

Drilling pilot holes to house the concrete anchors needed to hang a curtain rod on cement is an important step in the installation process. These screws are designed to secure the curtain brackets in place by anchoring into the concrete. 

How can I hang curtains on concrete walls with fasteners?

If you use the appropriate fasteners, mounting curtain rods in concrete is as simple as installing them on any other type of surface. 

In order to install the curtain rod hardware in cement, swap out the nails or screws that came with your rods for concrete fasteners. 

To install curtain rods in cement, you must first understand how to properly install concrete fasteners so that the curtain rods do not come loose from the wall.

Decide where you want the curtain rod hardware to be placed. If necessary, use a pencil or marker to make a hole for a screw through one side of curtain rod hardware while holding another side in place.

How to hang curtains on concrete walls with command hooks?

To hang your curtain rod, you’ll require at least two Command Hooks. It is necessary to use a third Command Hook if your window is wider than 30 inches.

Mark the locations on your wall where each curtain hook will be attached once you’ve carefully measured your curtains.

Apply the Command strip adhesive on the hook by peeling the backing off of it.

Bibliography 

KATHERINE KALLY. How to Hang Stuff on a Cement Wall. Retrieved from: https://www.hunker.com/13413711/how-to-hang-stuff-on-a-cement-wall