How to dissolve concrete in a drain pipe?

The article aims to answer the question “How to dissolve concrete in a drain pipe?”. It will also discuss the chemicals you could use to dissolve the concrete and what tools and equipment you may need. 

Read the article to know more:

How to dissolve concrete in a drain pipe?

• Pour hydrochloric acid down the blocked drain

• let it sit for two to three hours before flushing it out

• If the blockage persists, use four liters of water to flush the pipe and a plunger to dislodge it

• This should do the trick.

What do I need to dissolve concrete in a drain pipe?

• Liquid detergent
• Hydrochloric acid
• Baking soda
• Spray bottle 
• Sponge
• Mop
• Work gloves
• Safety glasses

How to dissolve concrete?

• Using a yard hose and clean, fresh water, wet down the dry concrete sections. Plastic drop cloths should be used to protect the surrounding surroundings.

• Put on a pair of safety goggles, a pair of eye protection, and a respirator mask. Pour five gallons of fresh water into a 5-gallon bucket made of all-plastic material. 

• When cleaning concrete or masonry, use a one-part acidic cleaning solution. The label on the container will tell you how much solution you need for each portion. In order to avoid an explosive reaction, never mix water to acid.

• Apply a substantial quantity of the solution to the areas you wish to dissolve concrete using a stiff-bristle nylon brush dipped in the prepared solution. Remove the concrete by scrubbing the surface with a brush.

• This method should be repeated as many times as required to get the desired outcome. Remove the drop cloths and rinse the cleansed areas with freshwater.

What chemicals can I use to dissolve concrete in a drain pipe?

You can use Cemix concrete dissolver to dissolve concrete in a drain pipe.

There are no sulfuric, muriatic, hydrochloric, or phosphoric acids in the “mineral-acid” Cemix Concrete Dissolver. It is completely biodegradable, non-toxic, and ecologically friendly, and there are no smells. 

In concrete, it targets the cement and totally dissolves hardened concrete, which may be washed away with a high-pressure washer using regular tap water. Cement, concrete, mortar, grout, and any other product containing cement may be removed using this method. 

For dissolving hardened concrete on Ready-Mix Trucks and Vehicles, Forms, Molds, Joinery, Brick, WheelBarrows, Pumps, Trowels, Screed, Concrete Saws and Slip-Form Pavers and Auger it is very beneficial. 

The product does not include any acid and is thus safe to use on painted or varnished objects, as well as on metal, plastic, or any other sort of plant life. Neutralization and dilution with water are simple. 

Correct application of the liquid to the substance is critical to success since it is fast-acting but not immediate. With this labor-saving device, you won’t have to worry about damaging your tools or equipment since you won’t have to pound on them or scrape them with acid.

How to dissolve concrete with acid in a drain pipe?

• Put on your safety goggles, gloves, and long apron before beginning work. The skin and eyes may be harmed by even mild acids.

• Obtain an open container of baking soda, as well as an extension hose, and place it near the area you’re working on. Acid spills may necessitate the use of these. Make sure the flora around you is sprayed with water and a limestone powder in case the acid gets on it.

• If you don’t want the acids to get on your carpet or lawn, lay down a plastic sheet. While cleaning the concrete in your home, open your windows to allow fresh air to circulate. Extra ventilation is required.

• Use a combination of phosphoric acid or trisodium phosphate and water specified by the manufacturer to clean the concrete first. Scrub acid into concrete with a brush. 

• These are less potent acids, but they may be able to dissolve enough concrete to be useful. Scrape the concrete you’re attempting to disintegrate with a putty knife after the acids have absorbed into the concrete for approximately a minute.

• Make sure the area is clean by sprinkling it with water. Determine whether a stronger acid is required.

• Use a strong plastic bucket to combine your muriatic acid and water. Ten parts water to one part muriatic acid is a popular ratio; nonetheless, observe the bottle’s instructions. To prevent possible acid spatter, never pour water into the acid; instead, pour the acid into the water.

• To dissolve the concrete, pour the acid mixture over it in a slow, steady stream. Using a brush and allowing it to soak for at least one minute is recommended. Remove the concrete you’re dissolving with a scraper after a minute or two.

• Use water to remove the acid and any dissolved concrete. Calcium carbonate, a fine powder, is what you’re looking for.

How to dissolve concrete with vinegar in a drain pipe?

• Pour white distilled vinegar into your spray container and shake well. This is a vinegar-only product; there is no water in it. Apple cider vinegar is another option; but, because of its hue, it may discolor your concrete.

• Vinegar may be used to clean your equipment.

• Wait no less than five minutes before rinsing the surface with vinegar. Although you may leave it overnight, it is not suggested because of the acidity of vinegar, which can eat away at the concrete more quickly the longer it is left on the surface.

• Use plenty of water to properly clean the dish.

• Check to check whether everything is as spotless as you’d want it to be! If not, continue Step 2 after drying.

• Make a thick paste in a bowl with 14 cup baking soda, 1 tbsp liquid dish detergent, and just enough distilled white vinegar.

• Allow it to settle on the surface for a few minutes. In most cases, five minutes is plenty of time.

• To clean, use warm water and a soft cloth.

Conclusion

Once solidified in the drain pipe, concrete is a tough substance that requires specific dissolving agents to remove. To remove concrete residue from masonry work, phosphoric acid and trisodium phosphate are the most often utilized chemicals. 

That doesn’t work all the time. Then use muriatic acid, an industrial grade of hydrochloric acid—but only after washing away the other acids and putting on the proper safety gear.

Frequently asked questions (FAQS): How to dissolve concrete in a drain pipe?

How to dissolve concrete in a drain pipe?

Pour hydrochloric acid down the blocked drain. let it sit for two to three hours before flushing it out. If the blockage persists, use four liters of water to flush the pipe and a plunger to dislodge it. This should do the trick.

How to dissolve concrete?

Using a yard hose and clean, fresh water, wet down the dry concrete sections. Plastic drop cloths should be used to protect the surrounding surroundings. Put on a pair of safety goggles, a pair of eye protection, and a respirator mask. Pour five gallons of fresh water into a 5-gallon bucket made of all-plastic material. 

When cleaning concrete or masonry, use a one-part acidic cleaning solution. The label on the container will tell you how much solution you need for each portion. In order to avoid an explosive reaction, never mix water to acid.

What chemicals can I use to dissolve concrete in a drain pipe?

You can use Cemix concrete dissolver to dissolve concrete. There are no sulfuric, muriatic, hydrochloric, or phosphoric acids in the “mineral-acid” Cemix Concrete Dissolver. It is completely biodegradable, non-toxic, and ecologically friendly, and there are no smells. 

In concrete, it targets the cement and totally dissolves hardened concrete, which may be washed away with a high-pressure washer using regular tap water. Cement, concrete, mortar, grout, and any other product containing cement may be removed using this method. 

Bibliography

William Machin. How to Dissolve Concrete. Retrieved from: https://homeguides.sfgate.com/how-to-dissolve-concrete-13401902.html

DAN HARKINS. How to Dissolve Concrete With Acids. Retrieved from: https://www.hunker.com/13402064/how-to-dissolve-concrete-with-acids